1. Electrical PMC & Plant Engineering Design Consulting
- Basic & Detailed Engineering: SLDs, Equipment Sizing, Layouts, Cable Routing, Earthing, Lightning Protection
- SCADA, ECMS & Power Management Systems: Network Design, Load Shedding Studies
- Procurement & Vendor Support: Specification Development, TBE, Budgeting, Contract Assistance
- Construction Supervision & Quality Control: Site Inspections, Compliance Verification
- Testing & Commissioning (Super vision): FAT, SAT, SCADA/BMS Integration
- SAFOP review and assistance
- Electrical System Design (LV, MV, HV, EHV)
- Layouts: Substation, power, Cable tray and trench, earthing and lightning protection and lighting layout
- Electrical equipment : HT/LT VFD, HT/LT Motors, HT/LT Switchgear/Control gear, Cables, Bus Duct, DG set, AC / DC UPS, Electric heat trace, Battery, Fire Alarm system.
- Mechanical packages like GTG HVAC, pumps, compressors, fans, EOT Crane, etc.
- Electrical SCADA, fault monitoring, ECMS and integration with Process DCS System and automation and Telecommunication & protection system.
- ETAP studies, Equipment Sizing & Technical Specification
- Procurement, Vendor Evaluation & FAT/SAT and Project Coordination & Interdisciplinary Review
- SmartPlant Electrical, Navisworks, SAP
- Compliance with BIS, IEEE, IEC, NEC Standards
2. HV/EHV Transmission & Distribution Consulting
- High Voltage Substation Design: Substation design with GIS & AIS up to 132/220kV Systems and Underground Cable Routing
- Emergency Power & Redundancy Planning: DG Sets, UPS, DRUPS
- 132kV package with GIS, cables SCADA and RTU integration and Telecommunication & protection system
- 132 kV GIS substation in container
- Regulatory & Safety Compliance: IEC, IEEE, ANSI/NEMA Standards
- System Study reports review
- Station Auxiliary transformers and Electrical system with switchgear and DC UPS, EDG etc.
3. Electrical Consulting for Data Centers
- Data Center Power System Design: Load forecasting, N+1 & 2N redundancy, UPS & Generator sizing
- Data Center Engineering: Feasibility studies, site selection (TIA-942B), load analysis, SLDs, redundancy design (N+1 / 2N), structured cabling, and IBMS / BMS / CCTV / PAGA / Fire Alarm integration.
- Electrical Infrastructure: Busbar trunking, earthing & lightning protection
- Power Quality & Efficiency: Harmonic analysis, PUE optimization, voltage drop studies
- Backup Power Solutions: Diesel Rotary UPS (DRUPS), ATS/STS integration for zero downtime
- SCADA, BMS & Power Monitoring Integration: Real-time energy monitoring, failure diagnostics
4. Fire Protection System Consulting
- Fire & Gas Detection and supression Systems: Smoke detectors, Gas Detectors, VESDA, Gas Release Panel, Fire Dampers, NOVAC / AEROSOL Cylinder & piping, Manual Call Points and Fire Controller panel Flame, Smoke, Heat Sensors, Gas Leak Detection
- Active Fire Suppression: FM-200, CO2 suppression, NOVAC / AEROSOL, and Sprinkler Systems
- Interface with SCADA & Building Management Systems (BMS)
- Compliance with NFPA, FM Global, & Local Fire Codes
- Vendor Coordination & Procurement Support : Specification Development, Technical Bid Evaluation
5. Telecommunication, Security & Access Control Systems Consulting
- Telecommunication System Design : Fiber Optic Networks, Structured Cabling, IP Telephony
- Security Surveillance (CCTV) System Engineering: IP Cameras, Motion Sensors
- Access Control Systems: Biometric, RFID, Smart Card, Face Recognition Integration
- Public Address & Emergency Communication Systems (PA/GA Systems)
- Radio system and Audio Visual system
- LAN/WAN, SDH, PAGA, CCTV, Access Control, Radio (TETRA/DMR), Emergency Telephones, and Fiber Network architecture